Home > PAINT & SUNDRIES > PAINT & STAINS > WATERPROOFERS & SEALERS > CONCRETE SEALERS
Sort By:
Page of 1
Quikrete 8730-02 Concrete Cure and Seal SEALER ACRYLIC SOLVENT GLO CLR United Gilsonite 22113 Masonry Waterproofer
Quikrete? Acrylic concrete cure & seal - satin finish (#8730) is a dual purpose water-based clear acrylic coating that cures freshly placed concrete and seals concrete and masonry surfaces. The sealer can be applied immediately after the finishing application and provides a durable semi-gloss finish. Dyco? Paver Sealer? is a solvent acrylic, "non-yellowing" water-proofing sealer designed to seal and protect bare/non-sealed cement pavers. Paver Sealer? gives a wet look appearance while enhancing the true colors of the paver. Paver Sealer? resists tire markings, cracking and peeling. Paver Sealer? is easy to apply and provides a mildew-resistant barrier. Dyco? 7200 cement Paver Sealer? is a solvent acrylic, non-yellowing clear sealer for sealing non-sealed or coated pavers. Paver Sealer? gives a wet look and enhances the true color of the paver. How to determine if your pavers have been sealed with a latex water base sealer: Test the surfaces by pouring a small amount of water on the surface. If it penetrates quickly, the surface is porous and ready for 7200 Paver Sealer?. If it does not and takes 2 to 20 min to penetrate, then do not apply 7200 Paver Sealer?. DRYLOK? natural look sealer is a non-yellowing protective coating that can be used as a sealer or concrete curing membrane. As a sealer, DRYLOK? natural look sealer penetrates deep to seal and protect masonry against acids, alkalis, road salts, de-icing compounds, household cleaners, gasoline, oil and weathering. Protects against dusting, staining and spalling. As a concrete hardener, When applied to freshly poured concrete, after the surface has set for 24 hrs and excess water has been removed, DRYLOK? natural look sealer will control water evaporation resulting in maximum concrete hardness.
PROTECTOR CONCRETE CLEAR 1GAL SEALER CONCRETE CLEAR GAL     SEALER CONCRETE GRAY GAL
Just like natural and man-made stone, concrete and masonry are porous materials. They will start to break down, dust, pit, crack and/or stain easily when subjected to weather, water, oil and UV rays. The only way to prevent damage and deterioration is to protect surfaces with a good quality sealer. Latex base Drylok? Concrete Protector provides clear, weatherproof protection against deterioration caused by de-icing salts, household cleaners, acid, gasoline, oil and weathering. Formulated with our exclusive SALTLOK? Technology, it penetrates into the surface and provides superior resistance to unsightly efflorescence stains (salt deposits) that are often visible on brick, block and poured concrete surfaces. Henry? 635 is a high-performance, high solids concrete sealer that is easy to apply, quick drying, nonflammable and UV stable. Applied at a minimum of two coats, Henry 635 is designed to protect all exterior absorbent concrete and masonry surfaces on residential and commercial applications, including driveways, sidewalks, patios, courtyards, walkways, pool decks and most vertical concrete surfaces. It is especially suited to seal Henry toppings and the gray version can be used to create a uniform appearance over both a repaired area and the adjacent concrete or masonry surfaces. Henry 635 is durable and abrasion-resistant when applied properly. Henry? 635 is a high-performance, high solids concrete sealer that is easy to apply, quick drying, nonflammable and UV stable. Applied at a minimum of two coats, Henry 635 is designed to protect all exterior absorbent concrete and masonry surfaces on residential and commercial applications, including driveways, sidewalks, patios, courtyards, walkways, pool decks and most vertical concrete surfaces. It is especially suited to seal Henry toppings and the gray version can be used to create a uniform appearance over both a repaired area and the adjacent concrete or masonry surfaces. Henry 635 is durable and abrasion-resistant when applied properly.
SEALER HI-GLOSS LATEX BASE    SEALER CONCRETE WET LOOK 1 GAL SEALER CONCRETE NATRAL LOOK 1G
DRYLOK? WetLook high-gloss sealer Just like natural and man-made stone, concrete and masonry are porous materials that will start to break down, dust, pit, crack and/or stain when subjected to weather, water, oil and UV rays. The only way to prevent damage and deterioration is to protect your surfaces with a good quality sealer. DRYLOK? wet look high-gloss sealer is a clear, non-yellowing, water-base sealer formulated for use on horizontal and vertical masonry surfaces where a high-gloss, WetLook finish is desired. ROCKSOLID? wet look concrete sealer seals and protects concrete and masonry surfaces from the damaging effects of water, chemicals and UV light. The water-base, film-forming formula provides a protective barrier to keep water out, protect against stains and extend the life of your concrete while leaving a wet look, high-gloss finish. ROCKSOLID? natural look concrete sealer seals and protects concrete and masonry surfaces from the damaging effects of water, chemicals and UV light. The water-base, film-forming formula provides a protective barrier to keep water out, protect against stains and extend the life of your concrete while leaving a natural look, low-gloss finish.
Homax 613 Wet Look Cure Seal MOISTURE STOP 1 GALLON        Drylok 22115 Natural Look Sealer
Protects from oil, rust, water and sprinkler stain penetration. Use on exposed aggregate, flagstone, concrete driveway, patio tile, walkway, and garage floor. Low odor and non-flammable. Leaves a clear natural wet look. Ready for traffic 8 to 24 hours. Apply with roller, brush, sponge, mop or airless sprayer. Covers 150 to 400 sq. ft. per gallon depending on porosity. RUST-OLEUM Moisture stop penetrates into concrete and reacts with the free calcium and water to form a gel in cracks, pores and capillaries to protect against the ingress of water and contaminants. This allows surfaces that were previously uncoatable, due to moisture, to be coated. DRYLOK? natural look sealer is a non-yellowing protective coating that can be used as a sealer or concrete curing membrane. As a sealer, DRYLOK? natural look sealer penetrates deep to seal and protect masonry against acids, alkalis, road salts, de-icing compounds, household cleaners, gasoline, oil and weathering. Protects against dusting, staining and spalling. As a concrete hardener, When applied to freshly poured concrete, after the surface has set for 24 hrs and excess water has been removed, DRYLOK? natural look sealer will control water evaporation resulting in maximum concrete hardness.
Valspar 82390 Wet Look Sealer Valspar 82092 Natural Look Waterproofer PROTECTOR CONCRETE CLEAR 5GAL
Valspar? wet look high-gloss sealer waterproofs and enhances the color and design of aggregate, masonry, brick, slate and pavers with a glossy, wet-look sheen. As durable as it is beautiful, it protects against the sun's powerful rays, damaging weather, water, gasoline and de-icing salts. Valspar? natural look protective sealer locks out weather and scuffs with a tough, penetrating layer of invisible protection. Just like natural and man-made stone, concrete and masonry are porous materials. They will start to break down, dust, pit, crack and/or stain easily when subjected to weather, water, oil and UV rays. The only way to prevent damage and deterioration is to protect surfaces with a good quality sealer. Latex base Drylok? Concrete Protector provides clear, weatherproof protection against deterioration caused by de-icing salts, household cleaners, acid, gasoline, oil and weathering. Formulated with our exclusive SALTLOK? Technology, it penetrates into the surface and provides superior resistance to unsightly efflorescence stains (salt deposits) that are often visible on brick, block and poured concrete surfaces.
Valspar 82390 Wet Look Sealer Valspar 82092 Natural Look Waterproofer SEALER ACRYLIC SOLVENT GLO CLR
Valspar wet look high gloss sealer waterproofs and enhances the color and design of concrete, brick, masonry, slate and pavers with a glossy, wet-look sheen. This sealer is formulated to protect your exterior surfaces against the sun's UV rays and damaging weather. Resists gasoline, oil and de-icing salts. Valspar natural look waterproofer forms a long lasting, waterproofing seal on concrete, brick, masonry, aggregate, natural stone and pavers. This sealer is formulated to protect against the sun's UV rays, water, gasoline and de-icing salts. This protective sealer allows the natural look of the surface to come through. Dyco? Paver Sealer? is a solvent acrylic, "non-yellowing" water-proofing sealer designed to seal and protect bare/non-sealed cement pavers. Paver Sealer? gives a wet look appearance while enhancing the true colors of the paver. Paver Sealer? resists tire markings, cracking and peeling. Paver Sealer? is easy to apply and provides a mildew-resistant barrier. Dyco? 7200 cement Paver Sealer? is a solvent acrylic, non-yellowing clear sealer for sealing non-sealed or coated pavers. Paver Sealer? gives a wet look and enhances the true color of the paver. How to determine if your pavers have been sealed with a latex water base sealer: Test the surfaces by pouring a small amount of water on the surface. If it penetrates quickly, the surface is porous and ready for 7200 Paver Sealer?. If it does not and takes 2 to 20 min to penetrate, then do not apply 7200 Paver Sealer?.