Home > PAINT & SUNDRIES > PAINT & STAINS > WATERPROOFERS & SEALERS
Choose a sub category:
CONCRETE SEALERS MULTI-SURFACE SEALERS MASONRY WATERPROOFERS
FOUNDATION COATINGS
Sort By:
Page of 1
WaterSeal 10100 Multi-Surface Waterproofer WaterSeal TH.024104-14 Multi-Surface Waterproofer Damtite 01071 Waterproofer Powder
Convenient waterproofing spray that provides proven waterproofing protection for wood, concrete and brick. Proven to waterproof wood, concrete and brick. Use as a wood sealer, brick sealer or for concrete waterproofing. A Portland cement-based, waterproofing coating for sealing, protecting & decorating wall sand surfaces constructed of poured concrete, concrete, cinder block, masonry, stone, brick or stucco. Safe coating for sealing the inside of drinking water concrete tanks and cisterns. Eliminates dampness, resists mold, mildew & flaking, chalking while beautifying and sealing all pores & voids. Unlike ready-mix paints which can only be applied to dry surfaces, this product is made for use on wet or dry surfaces. It also reduces Radon gas infiltration. Wear protective gloves and goggles.
Drylok 00542 Masonry Waterproofer Henry PR1760074 Premier Foundation Coating CONCRETE WATER REPELLENT 1GA
DRYLOK? powdered masonry waterproofer is formulated to fill and seal porous masonry walls against water, even under pressure, by becoming an actual part of the original surface. An aggregate type material, DRYLOK? powdered masonry waterproofer is ideal as a base coat, as well as a finish coat. Environmentally friendly. Asphalt Emulsion. For spray or brush application to existing or new, green or damp concrete and masonry surfaces. For below-greade applications to foundations, both poured concrete and CMU block. No odor, soap and water cleanup. Safe, odorless, clear penetrating sealer. Protects against water, ice and salt damage.
Damtite 03550 Masonry Waterproofer SEALER ACRYLIC SOLVENT GLO CLR Gardner-Gibson 0125-GA Roof And Foundation Coating
High-performance masonry waterproofers used for above or below-grade applications. Alkali-resistant coating provides excellent waterproofing protection with a decorative finish for all masonry, cinder and concrete block, poured concrete, brick, stucco, basement, retaining walls and foundations. Fast drying, low odor, tintable and easy to clean up. Reduces radon gas penetration through concrete block walls. Covers up to 125 sq-ft/gal. Dyco? Paver Sealer? is a solvent acrylic, "non-yellowing" water-proofing sealer designed to seal and protect bare/non-sealed cement pavers. Paver Sealer? gives a wet look appearance while enhancing the true colors of the paver. Paver Sealer? resists tire markings, cracking and peeling. Paver Sealer? is easy to apply and provides a mildew-resistant barrier. Dyco? 7200 cement Paver Sealer? is a solvent acrylic, non-yellowing clear sealer for sealing non-sealed or coated pavers. Paver Sealer? gives a wet look and enhances the true color of the paver. How to determine if your pavers have been sealed with a latex water base sealer: Test the surfaces by pouring a small amount of water on the surface. If it penetrates quickly, the surface is porous and ready for 7200 Paver Sealer?. If it does not and takes 2 to 20 min to penetrate, then do not apply 7200 Paver Sealer?. A thin, liquid-applied coating designed to seal and penetrate exterior concrete and masonry surfaces while providing a moisture barrier. It can also be used as an anti-corrosive coating for below-grade steel or metal piping. Seals and protects wood footings from decay and termites. For exterior use only.
Henry RC065070 Roofers Choice Foundation Coating United Gilsonite 22113 Masonry Waterproofer FBRWL SURF BONDING CEM WH 50LB
Cures to a tough, flexible, weather-resistant film. Because of its ability to retain its pliability, the coating resists damage which may result from expansion and contraction caused by weather and temperature variation. Use as an exterior underground foundation coating and dampproofer for brick, concrete, cement block and similar surfaces. May be used as an underground exterior foundation coating and dampproofer. Covers approximately 1 to 2 gal per 100 sq-ft. DRYLOK? natural look sealer is a non-yellowing protective coating that can be used as a sealer or concrete curing membrane. As a sealer, DRYLOK? natural look sealer penetrates deep to seal and protect masonry against acids, alkalis, road salts, de-icing compounds, household cleaners, gasoline, oil and weathering. Protects against dusting, staining and spalling. As a concrete hardener, When applied to freshly poured concrete, after the surface has set for 24 hrs and excess water has been removed, DRYLOK? natural look sealer will control water evaporation resulting in maximum concrete hardness. FiberWall? is an alkali-resistant, fiberglass-reinforced, Portland cement-base surface bonding cement with sand, used for construction of concrete block walls by dry-stack (without mortar). It is also ideal to waterproof, strengthen, rehabilitate, reinforce, restore and beautify various existing deteriorating surfaces, including chimneys, retaining walls and other concrete, brick, stone, tile or stucco areas above and below grade, on the interior and exterior.
FBRWL SURF BONDING CEM GR 50LB LATEX WATERPROOFER WHITE 1GA Damtite 01351 Supertite Masonry Waterproofer
FiberWall? is an alkali-resistant, fiberglass-reinforced, Portland cement-base surface bonding cement with sand, used for construction of concrete block walls by dry-stack (without mortar). It is also ideal to waterproof, strengthen, rehabilitate, reinforce, restore and beautify various existing deteriorating surfaces, including chimneys, retaining walls and other concrete, brick, stone, tile or stucco areas above and below grade, on the interior and exterior. Damtite Ultima is a low-odor, high-performance masonry waterproofer with a bright white finish. Ideal for interior and exterior, above and below grade applications. This durable, alkali-resistant coating provides excellent waterproofing protection with a slightly textured, decorative finish for all masonry, cinder and concrete block, poured concrete, brick, stone, stucco, basement, garage and retaining walls and foundations. No pre-mixing or pre-wetting is needed. Stops over 25 psi of hydrostatic water pressure. Fast drying with easy soap and water clean-up. Heavy-duty, Portland cement-based waterproofing coating with dry polymer-modified additive for excellent adhesion. Eliminates need for liquid bonding additive to mix for non-porous, smooth surfaces. Ideal for sealing, protecting and decorating vertical walls and surfaces constructed of concrete, masonry, stone, brick or stucco. Eliminates dampness, resists mold/ mildew and flaking or chalking while beautifying and sealing all pores and voids. Formulated for application directly onto damp or wet surfaces.
Henry PR175070 Premier Foundation Coating Henry PR175042 Premier Foundation Coating Damtite 02501 Waterproof Coating
A cold applied liquid asphalt in a solvent system. Penetrating type coating formulated to provide a durable, weather-resistant film. For long-wearing protection of foundation coating. Also use to dampproofing above and below-grade exterior concrete and masonry walls and foundations that are thoroughly dry. Covers 1.5 to 2 gal per 100 sq-ft. depending upon the porosity and roughness of the surface. Premier 175 Foundation Coating Non-Fibered dries to a tough, flexible, weather resistant film. Because of its ability to retain its flexibility, resists damage which may result from expansion and contraction caused by weather, temperature variation and normal building vibration. A gray Portland cement-base, waterproofing coating for sealing, protecting and decorating walls and surfaces constructed of poured concrete, concrete/cinder block, masonry, stone, brick or stucco. Ideal as parge coat for exterior, below-grade applications instead of using regular cement which does not waterproof. Safe coating for sealing the inside of drinking water concrete tanks and cisterns.
Zinsser 5001 Watertite Waterproofing Paint Drylok 27513 Ready-To-Use Concrete Sealer Damtite 01211 Waterproofer Powder
WATERTITE? professional Mold and Mildew-Proof? waterproofing paint has a unique oil-base formula that combines a state-of-the-art waterproofing resin with Portland cement to create a coating that stops up to 34 lb psi of water pressure. It also contains a mildewcide to prevent the growth of mold and mildew for a minimum of 10 years after application, making it great for basements and other masonry surfaces where mold and mildew can be problematic. Latex Base DRYLOK? Masonry waterproofer is the manageable way to solve water seepage problems. Reduces radon gas penetration by reducing vapor transfer. A Portland cement-based, waterproofing coating for sealing, protecting & decorating wall sand surfaces constructed of poured concrete, concrete, cinder block, masonry, stone, brick or stucco. Safe coating for sealing the inside of drinking water concrete tanks and cisterns. Eliminates dampness, resists mold, mildew & flaking, chalking while beautifying and sealing all pores & voids. Unlike ready-mix paints which can only be applied to dry surfaces, this product is made for use on wet or dry surfaces. It also reduces Radon gas infiltration. Wear protective gloves and goggles.
Damtite 01501 Waterproof Coating PROTECTOR CONCRETE CLEAR 1GAL Drylok 27613 Latex Based Masonry Waterproofer
Heavy-duty, Portland cement-base, waterproofing coating for sealing, protecting & decorating walls and surfaces constructed of poured concrete, concrete/cinder block, masonry, stone, brick or stucco. Safe coating for sealing the inside of drinking water concrete tanks and cisterns. Just like natural and man-made stone, concrete and masonry are porous materials. They will start to break down, dust, pit, crack and/or stain easily when subjected to weather, water, oil and UV rays. The only way to prevent damage and deterioration is to protect surfaces with a good quality sealer. Latex base Drylok? Concrete Protector provides clear, weatherproof protection against deterioration caused by de-icing salts, household cleaners, acid, gasoline, oil and weathering. Formulated with our exclusive SALTLOK? Technology, it penetrates into the surface and provides superior resistance to unsightly efflorescence stains (salt deposits) that are often visible on brick, block and poured concrete surfaces. Latex Base DRYLOK? Masonry waterproofer is the manageable way to solve water seepage problems. Reduces radon gas penetration by reducing vapor transfer.
SEALER CONCRETE CLEAR GAL SEALER CONCRETE GRAY GAL WaterSeal 24111 Multi-Surface Waterproofer
Henry? 635 is a high-performance, high solids concrete sealer that is easy to apply, quick drying, nonflammable and UV stable. Applied at a minimum of two coats, Henry 635 is designed to protect all exterior absorbent concrete and masonry surfaces on residential and commercial applications, including driveways, sidewalks, patios, courtyards, walkways, pool decks and most vertical concrete surfaces. It is especially suited to seal Henry toppings and the gray version can be used to create a uniform appearance over both a repaired area and the adjacent concrete or masonry surfaces. Henry 635 is durable and abrasion-resistant when applied properly. Henry? 635 is a high-performance, high solids concrete sealer that is easy to apply, quick drying, nonflammable and UV stable. Applied at a minimum of two coats, Henry 635 is designed to protect all exterior absorbent concrete and masonry surfaces on residential and commercial applications, including driveways, sidewalks, patios, courtyards, walkways, pool decks and most vertical concrete surfaces. It is especially suited to seal Henry toppings and the gray version can be used to create a uniform appearance over both a repaired area and the adjacent concrete or masonry surfaces. Henry 635 is durable and abrasion-resistant when applied properly. Proven to waterproof wood, concrete and brick. Use as a wood sealer, brick sealer or for concrete waterproofing.
Valspar 7276 Multi-Surface Waterproofing Sealer SEALER HI-GLOSS LATEX BASE Drylok 28613 Latex Based Masonry Waterproofer
Beads water to resist moisture damage. Dries to clear finish, soap and water cleanup. Use on wood, brick, concrete, masonry, stucco and porous surfaces. DRYLOK? WetLook high-gloss sealer Just like natural and man-made stone, concrete and masonry are porous materials that will start to break down, dust, pit, crack and/or stain when subjected to weather, water, oil and UV rays. The only way to prevent damage and deterioration is to protect your surfaces with a good quality sealer. DRYLOK? wet look high-gloss sealer is a clear, non-yellowing, water-base sealer formulated for use on horizontal and vertical masonry surfaces where a high-gloss, WetLook finish is desired. Latex base DRYLOK? EXTREME masonry waterproofer is the next generation in waterproof coatings. Features flexible encapsulated polymers which squeeze into the masonry for the ultimate in waterproof protection. Specially formulated to resist mildew growth on the dry paint film with the incorporation of an environmentally friendly green biocide. Fully transferable 15 years warranty. Tested to ASTM D-7088 Resistance to hydrostatic pressure at 15 psi and ASTM D6904 resistance to wind driven rain. Reduces Radon gas penetration.
WATERPROOF MASONRY GRAY 1G SEALER BRICK&MSNRY CLEAR 1GAL WaterSeal 24106 Multi-Surface Waterproofer
If water is leaking through existing masonry or you need to protect new construction, DRYLOK? extreme masonry waterproofer's proprietary formula is guaranteed to stop water. Unlike ordinary paint that simply adheres to a surface and can be forced off by incoming water pressure, DRYLOK? extreme masonry waterproofer actually penetrates the pores in that surface, bonding to the masonry and creating an impenetrable barrier. DRYLOK? siloxane 7 brick and masonry penetrating sealer is a clear, durable, water-repellent, specialty formulation for use on exterior, above-grade, vertical and horizontal brick and masonry surfaces. With just one coat, it minimizes the deterioration of masonry and mortar and helps control efflorescence (salt deposits) and surface staining. DRYLOK? siloxane 7 brick and masonry penetrating sealer prevents moisture penetration and eliminates plaster cracking, paint blistering and damp staining of interior finishes. Proven to waterproof wood, concrete and brick. Use as a wood sealer, brick sealer or for concrete waterproofing.
Valspar 7276 Multi-Surface Waterproofing Sealer SEALER CONCRETE WET LOOK 1 GAL SEALER CONCRETE NATRAL LOOK 1G
Beads water to resist moisture damage. Dries to clear finish, soap and water clean up. Use on wood, brick, concrete, masonry, stucco and porous surfaces. ROCKSOLID? wet look concrete sealer seals and protects concrete and masonry surfaces from the damaging effects of water, chemicals and UV light. The water-base, film-forming formula provides a protective barrier to keep water out, protect against stains and extend the life of your concrete while leaving a wet look, high-gloss finish. ROCKSOLID? natural look concrete sealer seals and protects concrete and masonry surfaces from the damaging effects of water, chemicals and UV light. The water-base, film-forming formula provides a protective barrier to keep water out, protect against stains and extend the life of your concrete while leaving a natural look, low-gloss finish.
SEALER MULTI-SURF CWF CLEAR GA WATERPROOFER MASONRY CLEAR 1G Damtite 02451 Waterproofer Powder
CWF? multi-surface is a clear waterproofing sealant that protects against moisture damage. It is recommended for use on brick, stucco, concrete, masonry and more. Waterproof interior, exterior, above or below grade walls. Unlike ordinary paint that simply adheres to a surface and can be forced off by incoming water pressure, DRYLOK? floor and wall masonry waterproofer actually penetrates the pores in that surface, bonding to the masonry and creating an impenetrable barrier. A Portland cement-based, waterproofing coating for sealing, protecting & decorating wall sand surfaces constructed of poured concrete, concrete, cinder block, masonry, stone, brick or stucco. Safe coating for sealing the inside of drinking water concrete tanks and cisterns. Eliminates dampness, resists mold, mildew & flaking, chalking while beautifying and sealing all pores & voids. Unlike ready-mix paints which can only be applied to dry surfaces, this product is made for use on wet or dry surfaces. It also reduces Radon gas infiltration. Wear protective gloves and goggles.
Homax 613 Wet Look Cure Seal MOISTURE STOP 1 GALLON Drylok 22115 Natural Look Sealer
Protects from oil, rust, water and sprinkler stain penetration. Use on exposed aggregate, flagstone, concrete driveway, patio tile, walkway, and garage floor. Low odor and non-flammable. Leaves a clear natural wet look. Ready for traffic 8 to 24 hours. Apply with roller, brush, sponge, mop or airless sprayer. Covers 150 to 400 sq. ft. per gallon depending on porosity. RUST-OLEUM Moisture stop penetrates into concrete and reacts with the free calcium and water to form a gel in cracks, pores and capillaries to protect against the ingress of water and contaminants. This allows surfaces that were previously uncoatable, due to moisture, to be coated. DRYLOK? natural look sealer is a non-yellowing protective coating that can be used as a sealer or concrete curing membrane. As a sealer, DRYLOK? natural look sealer penetrates deep to seal and protect masonry against acids, alkalis, road salts, de-icing compounds, household cleaners, gasoline, oil and weathering. Protects against dusting, staining and spalling. As a concrete hardener, When applied to freshly poured concrete, after the surface has set for 24 hrs and excess water has been removed, DRYLOK? natural look sealer will control water evaporation resulting in maximum concrete hardness.
SEALER MULTI-SURF CWF CLR 5GA Damtite 01451 Waterproofer Powder Valspar 82390 Wet Look Sealer
CWF? multi-surface is a clear waterproofing sealant that protects against moisture damage. It is recommended for use on brick, stucco, concrete, masonry and more. A Portland cement-based, waterproofing coating for sealing, protecting & decorating wall sand surfaces constructed of poured concrete, concrete, cinder block, masonry, stone, brick or stucco. Safe coating for sealing the inside of drinking water concrete tanks and cisterns. Eliminates dampness, resists mold, mildew & flaking, chalking while beautifying and sealing all pores & voids. Unlike ready-mix paints which can only be applied to dry surfaces, this product is made for use on wet or dry surfaces. It also reduces Radon gas infiltration. Wear protective gloves and goggles. Valspar? wet look high-gloss sealer waterproofs and enhances the color and design of aggregate, masonry, brick, slate and pavers with a glossy, wet-look sheen. As durable as it is beautiful, it protects against the sun's powerful rays, damaging weather, water, gasoline and de-icing salts.
Valspar 82092 Natural Look Waterproofer PROTECTOR CONCRETE CLEAR 5GAL WaterSeal TH.023111-03 Waterproofer Masonry Protector
Valspar? natural look protective sealer locks out weather and scuffs with a tough, penetrating layer of invisible protection. Just like natural and man-made stone, concrete and masonry are porous materials. They will start to break down, dust, pit, crack and/or stain easily when subjected to weather, water, oil and UV rays. The only way to prevent damage and deterioration is to protect surfaces with a good quality sealer. Latex base Drylok? Concrete Protector provides clear, weatherproof protection against deterioration caused by de-icing salts, household cleaners, acid, gasoline, oil and weathering. Formulated with our exclusive SALTLOK? Technology, it penetrates into the surface and provides superior resistance to unsightly efflorescence stains (salt deposits) that are often visible on brick, block and poured concrete surfaces. Provides proven waterproofing protection for all masonry surfaces including pavers, brick, concrete, stone, stucco, clay and quarry tile. Use for concrete waterproofing and as a brick sealer.
Drylok 27515 Latex Based Masonry Waterproofer Drylok 27615 Masonry Waterproofing Paint Valspar 82390 Wet Look Sealer
Latex Base DRYLOK? Masonry waterproofer is the manageable way to solve water seepage problems. Reduces radon gas penetration by reducing vapor transfer. Latex Base DRYLOK? Masonry waterproofer is the manageable way to solve water seepage problems. Reduces radon gas penetration by reducing vapor transfer. Valspar wet look high gloss sealer waterproofs and enhances the color and design of concrete, brick, masonry, slate and pavers with a glossy, wet-look sheen. This sealer is formulated to protect your exterior surfaces against the sun's UV rays and damaging weather. Resists gasoline, oil and de-icing salts.
Valspar 82092 Natural Look Waterproofer Cabot 1000 Waterproofing Sealer Zinsser Watertite Waterproofing Paint
Valspar natural look waterproofer forms a long lasting, waterproofing seal on concrete, brick, masonry, aggregate, natural stone and pavers. This sealer is formulated to protect against the sun's UV rays, water, gasoline and de-icing salts. This protective sealer allows the natural look of the surface to come through. Cabot waterproofing is an advanced technology silicone sealer that provides unsurpassed waterproofing protection to a multitude of surfaces. This convenient and simple-to-use formulation penetrates and fills the pores of the substrate with a premium-grade silicone sealer and unlike waxes, silicone will impart a lasting repellency to any surface to which it is applied. ZINSSER? WATERTITE? mold and mildew-resistant waterproofing paint is a low odor, oil-based waterproofing paint designed to waterproof interior and exterior concrete, stucco, cement, cinder block and other masonry surfaces. It is ideal for interior basement walls and for sealing concrete basement slabs prior to installing flooring. It is not recommended for foot traffic. It is also ideal for exterior foundations and retaining walls, above and below-grade.
Damtite 03555 Masonry Waterproofer Cabot 1000 Waterproofing Sealer Drylok 28615 Extreme Masonry Waterproofing Paint
High-performance masonry waterproofers used for above or below-grade applications. Alkali-resistant coating provides excellent waterproofing protection with a decorative finish for all masonry, cinder and concrete block, poured concrete, brick, stucco, basement, retaining walls and foundations. Fast drying, low odor, tintable and easy to clean up. Reduces radon gas penetration through concrete block walls. Covers up to 125 sq-ft/gal. Cabot waterproofing is an advanced technology silicone sealer that provides unsurpassed waterproofing protection to a multitude of surfaces. This convenient and simple-to-use formulation penetrates and fills the pores of the substrate with a premium-grade silicone sealer and unlike waxes, silicone will impart a lasting repellency to any surface to which it is applied. Latex base Drylok? Extreme masonry waterproofer is the next generation in waterproof coatings. Features flexible encapsulated polymers which squeeze into the masonry for the ultimate in waterproof protection. Specially formulated to resist mildew growth on the dry paint film with the incorporation of an environmentally friendly green biocide. Fully transferable 15 years warranty. Tested to ASTM D-7088 Resistance to hydrostatic pressure at 15 psi and ASTM D6904 resistance to wind driven rain. Reduces Radon gas penetration.
LATEX WATERPROOFER WHITE 5GA WATERPROOF MASONRY WHITE 5G SEALER ACRYLIC SOLVENT GLO CLR
Damtite ULTIMA is a low-odor latex masonry waterproofer, formulated with mildewcide to prevent mold/mildew growth on a dry paint film and with ceramic to provide a whiter, smoother finish. For interior and exterior, above & below grade applications. Durable, alkali-resistant coating provides excellent waterproofing protection with a decorative finish for all masonry, cinder and concrete block, poured concrete, brick, stucco, basement, garage and retaining walls and foundations. No pre-mixing or pre-wetting is needed. Fast drying with easy soap and water cleanup. Stops 30 psi of hydrostatic pressure. Includes fully transferable 15 year warranty. Waterproof interior, exterior, above or below grade walls. Unlike ordinary paint that simply adheres to a surface and can be forced off by incoming water pressure, DRYLOK? floor and wall masonry waterproofer actually penetrates the pores in that surface, bonding to the masonry and creating an impenetrable barrier. Dyco? Paver Sealer? is a solvent acrylic, "non-yellowing" water-proofing sealer designed to seal and protect bare/non-sealed cement pavers. Paver Sealer? gives a wet look appearance while enhancing the true colors of the paver. Paver Sealer? resists tire markings, cracking and peeling. Paver Sealer? is easy to apply and provides a mildew-resistant barrier. Dyco? 7200 cement Paver Sealer? is a solvent acrylic, non-yellowing clear sealer for sealing non-sealed or coated pavers. Paver Sealer? gives a wet look and enhances the true color of the paver. How to determine if your pavers have been sealed with a latex water base sealer: Test the surfaces by pouring a small amount of water on the surface. If it penetrates quickly, the surface is porous and ready for 7200 Paver Sealer?. If it does not and takes 2 to 20 min to penetrate, then do not apply 7200 Paver Sealer?.