|
|
|
|
|
|
|
|
|
|
|
|
|
|
Specially scored waxed screws. Scored head breaks off at the same place every time. Carded.
|
Keep your Quik Drive auto-feed screw driving system in ideal condition with these Simpson Strong-Tie? replacement parts.
|
The Squeek No More kit is designed to stop floor squeaks from above the floor by going safely through the carpet. The kit works on all carpets even berber. The Squeek No More kit has 50 screws that are scored one inch from the head and coated with a special wax that allows the screw to safely pass through the carpet. The tooling, a tripod fixture and driver bit, drives the screw safely through the carpet stopping the score on the screw slightly below the wood of the floor. Then with the tripod fixture you snap the head of the screw off. The screw thread then holds the floor to the joist without having any part of the screw sticking up that you could walk on. The kit also includes 2 joist finding tools. You use these to quickly and accurately find the joist from above the floor.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The WBSK workbench and shelving hardware kit provides the connectors and connector fasteners to build a workbench or shelving unit. The kit features the Simpson Strong-Tie? Rigid Tie? RTC2Z corner connector that makes it easier to make strong and durable corner connections with 2 x 4 lumber using no angle cuts or bolts. Each kit contains enough RTC2Z connectors to construct one workbench. Two kits are necessary to build a four-shelf unit. With the WBSK kit, a professional quality project can be customized and completed in a couple of hours.
|
You determine the size. Connect with railing brackets with 2x4 and 2x6 lumber to easily add a bench to any size or shape deck. Gain increased seating area while using only 7 in of deck space. Assembled unit stands 36 in H for deck railing, seat is 17 in H. Quick and easy to assemble using basic tools. Includes bench bracket, hardware and instructions. Lumber not included.
|
You can determine the size and configuration, just add 2x4's to the ShelfLinks to make functional and custom shelving in any length, height and configuration. Made of structural resin. Can support spans up to 8 ft. Includes ShelfLinks, hardware and instructions. Lumber not included.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
When using the Grabber Deckmaster fastening system, all fasteners are hidden beneath the deckboards. There is no surface penetration of the deckboards or joists. With Grabber Deckmaster there are no exposed screws a primary entry point for moisture and deck board damage. No stains or splinters form around fastener holes.
|
When using the Deckmaster fastening system, all fasteners are hidden beneath the deckboards. There is no surface penetration of the deckboards or joists. With Deckmaster there are no exposed screws a primary entry point for moisture and deck board damage. No stains or splinters form around fastener holes.
|
When using the Grabber Deckmaster fastening system, all fasteners are hidden beneath the deckboards. There is no surface penetration of the deckboards or joists. With Grabber Deckmaster there are no exposed screws a primary entry point for moisture and deck board damage. No stains or splinters form around fastener holes.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Make a comfortable, sturdy bench and a table up to 8 ft long. Just add 2x4 lumber pieces. Flips and locks from a bench to a table in seconds without using tools. Slide lock safely secures and locks in position. Made of maintenance-free structural resin. Use only one or slide two Bench Tables together for a full size picnic table. Good for small porches and decks. Assembled unit stands 34 in H in the bench position, 31 in H in the table position and both with 17-1/2 in H seat. Includes Bench Table legs, hardware and instructions. Lumber not included.
|
The CNW is designed to connect threaded rods to one another and to anchor bolts. These coupler nuts are designed to exceed the specified minimum tensile capacity of the corresponding bolts and threaded rod. All CNW coupler nuts feature a positive stop to help ensure even threading into each end of the nut and a Witness? hole as a means to verify when rods are properly installed.
|
Create a workbench, worktable or power tool stand. Add 2x4's plywood or particleboard to make a workbench, worktable or power tool stand in any length or width up to 8 ft L x 4 ft W. Simple assembly in less than an hour with only powered screwdriver and a saw. Only straight, 90 deg cuts required, no miter or angles. Made of structural resin. Kit includes: 4 legs, hardware and instructions. Lumber and shelf links not included.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Bearing plates give greater bearing surface than standard-cut washers and help distribute the load at these critical connections. The LBPS are bearing plates that offer increased flexibility while meeting the latest requirements of the code for 2 x 4 and 2 x 6 walls. The slotted hole allows for adjustability to account for bolts that are not in the middle of the sill plate.
|
Bearing plates give greater bearing surface than standard-cut washers and help distribute the load at these critical connections. The LBPS are bearing plates that offer increased flexibility while meeting the latest requirements of the code for 2 x 4 and 2 x 6 walls. The slotted hole allows for adjustability to account for bolts that are not in the middle of the sill plate.
|
The SS is designed to reinforce notched, vertical studs in construction. This stud shoe is used to strengthen a wall stud that has a large hole drilled through it, typically to accommodate a plumbing waste line. The SS installs over the outside diameter of the pipe and is used as part of a total member replacement in structural applications.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
When using the Deckmaster fastening system, all fasteners are hidden beneath the deckboards. There is no surface penetration of the deckboards or joists. With Deckmaster there are no exposed screws a primary entry point for moisture and deck board damage. No stains or splinters form around fastener holes.
|
When using the Grabber Deckmaster fastening system, all fasteners are hidden beneath the deckboards. There is no surface penetration of the deckboards or joists. With Grabber Deckmaster there are no exposed screws a primary entry point for moisture and deck board damage. No stains or splinters form around fastener holes.
|
When using the Grabber Deckmaster fastening system, all fasteners are hidden beneath the deckboards. There is no surface penetration of the deckboards or joists. With Grabber Deckmaster there are no exposed screws a primary entry point for moisture and deck board damage. No stains or splinters form around fastener holes.
|
|
|
